Which method is a TCP/IP based protocol for establishing and managing connections between IP based storage dev ...


Which method does FCIP use to enable connectivity of geographically distributed Fibre Channel SANs over IP. ...


Which important feature on the front end is provided to the clients by multiple servers that access the same sto ...


The Ethernet specification details several different fiber optic media types. What is the wire transmission spee ...


Which fiber optic cable type is used most often with a Subscriber connector.


Which type of connection across the network does a SAN allow for multiple servers to access an unlimited amount ...


Which two statements about the Ethernet media are true. (Choose two.)


What is the wire transmission speed for 100GBASE ER4 Ethernet.


Which two statements about PCIe are true. (Choose two.)


Which three statements about FCoE are true. (Choose three.)


Which cable is used to access the command line interface of a Cisco UCS 6120XP Fabric Interconnects.


Where do you find the model number of a Cisco MDS 9200 Series chassis.


How do you find the serial number of a Cisco UCS 5108 Blade Server chassis.


What does the system status LED look like when an over temperature or major alarm occurs on the Cisco UCS 6120XP ...


Which processor option is supported in the Cisco UCS C420 M3 Server.


Which two major components does a Cisco Nexus 1000V Series Switch have. (Choose two.)


Which Cisco Nexus 5000 Series model supports 1/10G BASE T ports.


Which Cisco MDS model supports the most Fibre Channel ports per chassis.


Which supervisor module is supported by a Cisco Nexus 7700 Series Switch.


Which type of optics module is supported by a 12 port 100 GE Cisco Nexus 7700 F3 Series I/O module.


Which command line interface mode is best described by this prompt. UCS switch A (nxos) #


Which command can be used to exit to EXEC mode from this current mode. switch(config if) #


Which command saves the active configuration to NVRAM.


Which command syntax is correct to reset the admin password when the switch is in the kickstart prompt "switch(b ...


To do a password recovery on a Cisco NX OS Switch, which option shows the correct syntax to display the bootfla ...


Which Cisco NX OS command displays kernel uptime.


Which two commands display the version of Cisco NX OS code that the device is currently running on. (Choose t ...


On the Sensors page from the CIMC view, which four tabs are displayed to view further information. (Choose fou ...


Which three options are the minimum browser requirements to log into the Cisco CIMC GUI. (Choose three.)


Which tool does a network administrator not need when installing hardware.


When the Cisco UCS Manager is used to verify the B or C Series device, which two types of Overall Status are ...


What is the correct path to verify the Overall Status of Chassis 1 | Server 3.


If the Overall Status for a Cisco UCS B Series Blade Server indicates a failure in the Cisco UCS Manager, such ...


Which action should the administrator take before physically removing a blade server for maintenance or replacem ...


Which three statements about powering down a Cisco UCS C Series Rack Mount Server to perform maintenance or re ...


Which three components are hot swappable in a Cisco UCS Blade Server and Chassis. (Choose three.)


Which five things should the administrator verify after performing maintenance or replacing a blade server. (C ...


Which two statements about DIMM replacement in Cisco UCS Servers are true. (Choose two.)


Which three tools are necessary to console into a Cisco UCS C Series Rack Mount Server. (Choose three.)


After installation or replacement of a Cisco UCS C Series Rack Mount Server, the host does not boot. Which fou ...


Which three firmware components does the Host Upgrade Utility upgrade. (Choose three.)


Which two commands allow you to view the state of high availability between the two clustered Fabric Interconnec ...


Which three troubleshooting procedures do you perform when there is no power to a Cisco UCS B250 M2 Blade Server ...


Which two remote file system methods are used in the training material to transfer firmware to the Fabric Interc ...


On which three devices can the Host Upgrade Utility be performed. (Choose three.)


When a host firmware package policy is created, what must it be associated with to upgrade the BIOS.


Up to what speed can Category 5 UTP cable transmit data.


Up to what speed can Category 5e UTP cable transmit data.


What is the maximum distance that the 40GBASE LR4 Ethernet standard can span.


Which two statements about the Cisco Nexus 5596UP switch are true. (Choose two.)


Which two Cisco Nexus switches provide the foundation of the Cisco Application Centric Infrastructure. (Choose ...


Which type of optics module is supported by a 6 port 40 GE Cisco Nexus 7000 M2 Series I/O module.


How many 10GBASE T port licenses are preinstalled on a Cisco Nexus 3064 32T.


What is the maximum number of supervisor modules that the Cisco MDS 9710 Switch supports.


Which device provides analysis of Fibre Channel traffic without any network disruption.


Which three steps do you perform to troubleshoot when a rack server powers on with no video. (Choose three.) ...