A small manufacturing company has a Class C network address on the plant floor and needs to create fivesubnets, e ...


Exhibit: Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network


Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits tha ...


Exhibit: Refer to the exhibit. Which port should a PLC with IP address 192.168.3.65 be plugged into in order ...


Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion. ...


Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the ...


Exhibit: Which two statements are correct for a safe wiring installation to the terminal block of the switch o ...


What are two benefits of a star network topology. (Choose two.)


Which three of the following components must be elected before the Spanning Tree Protocol can converge in a swit ...


What is the purpose of Spanning Tree Protocol.


Exhibit: Refer to the exhibit. CCN


Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration. ...


Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link fail ...


Which two ports does EtherNet/IP use to communicate. (Choose two.) 82946689BACD434CCAFA8D24B56238B9


EtherNet/IP is an Ethernet implementation of which protocol.


Which prompt is used to configure parameters for the Ethernet ports of an industrial switch.


What are the two most relevant factors in determining the class of administration that is required to maintain t ...


According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control. ...


An administrator has connected devices to an industrial switch and, for security reasons, wants the dynamically ...


Exhibit: Refer to the exhibit. C router is to be used as a "router on a stick" to route between the VLANs. A ...


Which characteristic causes multimode fiber optic cable to differ from single mode.


Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is cl ...


For which three issues should fiber optic network segments be tested. (Choose three.)


What should be done with unused conductors in copper unshielded or shielded twisted pair network cables.


With what are APC connectors used.


A network administrator has subnetted the 172.16.0.0 network using a subnet mask of 255.255.255.192. A duplicate ...


An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the ...


You are troubleshooting a connectivity problem and want to isolate the problem. You suspect that a router on the ...


The network administrator is using a Windows PC application that is called putty.exe for remote communication to ...


What are two symptoms of duplex mismatch. (Choose two.)


With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber.


You are a called upon to troubleshoot connectivity problems to a network device on a production floor. You have ...


What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in di ...


In which two ways could you minimize the impact of monitoring an industrial network. (Choose two.)


What is the leading cause of fiber optic link failure.


At which Layer would you troubleshoot a cabling issue.


At which Layer would you check for spanning tree loops.


At which Layer would you use trace route to validate the path.


At which Layer would you check ACLs for TCP ports being blocked.


What two things does a router do when it forwards a packet. (Choose two.)


A router is not operating as expected and the network administrator wants to verify that the router booted using ...


What does the Cisco PSIRT issue for significant security issues that directly involve Cisco products and require ...


What is a reason to use privileged EXEC mode on an industrial switch.


What is a reason to use user EXEC mode on an industrial switch.


Which two pieces of information are commonly tracked as part of a change management process. (Choose two.)


What is the most critical step to perform when you are using optical fiber connectors.


What is a characteristic of cables that are used in articulating equipment arms.


Which three pieces of information must be maintained for all stakeholders as part of the change management proce ...


Exhibit: Refer to the exhibit. A technician enters the exhibited commands to configure a new router on the pla ...


Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is ...


With a Cisco IE 2000 switch, what does a power status LED indicate when it is solid green.


What is the purpose of a time domain reflectometer.


How does the optical time domain reflectometer use "backscattered" light to make measurements.


Which two commands can help you to determine what image is running on your industrial switch. (Choose two.) ...


Which protocol is a secure alternative to Telnet.


Which two reasons make mesh bonding systems most effective. (Choose two.)


What do deflections indicate to the time domain reflectometer user.


What are two benefits that are provided by proper grounding and bonding systems. (Choose two.)