Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that thedata is t ...


Refer to the exhibit. The Robot Cell is in a bottling plant. This cell environment needs to consider high flex, ...


Refer to the exhibit. Which three elements would enable high availability and predictable performance for a mot ...


You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. ...


Refer to the exhibit. CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this m ...


It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as op ...


Which five are characteristics that describe Cisco Industrial switches. (Choose five)


Which selection is a reason why IGMP snooping should be configured on a switched network.


Refer to the exhibit. Which three options are needed to configure NAT on router GW so PC1 and PC2 will be abl ...


Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol tha ...


If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the maj ...


Your supervisor calls you and tells you that one of the Stratix 5700 switches is not assigning all CIP explicit ...


Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI.


A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and ma ...


A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain ...


What is the reason that ProfiNET frames are discarded by default on Catalyst switches.


Which statement is true regarding ProfiSAFE.


Which statement is correct regarding ProfiNET communication classes.


Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP).


Which statement is correct regarding Media Redundancy Protocol (MRP) in a ring of ProfiNET devices.


Profinet has been disabled on a Cisco Industrial Ethernet switch, which CLI commands correctly enable ProfiNET o ...


Which command globally enables QoS on a Cisco Industrial Ethernet switch.


To ensure ProfiNET Layer 2 Class of Service markings from ProfiNET devices are trusted by the switch, which co ...


To correctly integrate a Cisco Industrial Ethernet switch into a ProfiNET management system such as SIMATIC STEP ...


Cisco Industrial Ethernet switches are capable of sending alarm messages to ProfiNET management stations using t ...


Which in depth approach is used when deploying defense in an industrial zone.


What can be done to increase the security in depth in an industrial zone.


Which two actions are examples of network device hardening for Cisco Industrial Ethernet Switches. (Choose two ...


Which three network mechanisms can be used for securely segmenting an industrial network. (Choose three)


Which two are possible solutions to control which devices can communicate between industrial zones. (Choose tw ...


Refer to the exhibit. Which values are correct for AP 2 to allow for efficient roaming.


Which describes the relationship between a workgroup bridge.


Which scenario represents the correct configuration to support the SSIDs of this autonomous access point. A ) ...


AP CAPWAP control traffic should be isolated from wireless client traffic. Which scenario represents the correct ...


What are three Cisco best practices for running I/O control traffic in a wireless environment. (Choose three) ...


When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.


A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet sw ...


A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC manage ...


Your controller has a high performance EtherNet/IP interface with port speed of >30,000 packets per second an ...


Refer to the exhibit. Which lines represent a CIP connection being established between two devices.


You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch that was deployed using the E ...


After commissioning several Stratix 5700 switches in a ring topology, you want to verify the installation agains ...


What percentage of an I/O connection would you set the RPI in order to ensure the application has the most curre ...


How are I/O timeout and Safety I/O timeout calculated.


You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on line with R ...


Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the pri ...


It is determined that an intermittent high packet loss event is occurring within a segment of the network. The a ...


Which best describes the difference between 802.11n and 802.11ac.


Which describes a best practice rule for controlling traffic between the corporate network and the controls netw ...


Refer to the exhibit. Network Faceplates have not been installed on the HMI and so you need to map a network b ...


Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch.


Refer to the exhibit. The control system depicted in the exhibit uses VLAN 300 for all of its device ports and ...


Refer to the exhibit. An expansion project added an E Tap and Device Level Ring to interface FastEthernet1/1 ...


Refer to the exhibit. L3SW1 has a spanning tree priority of 8192 set on VLANs 1, 300, and 301, and these VLAN ...


Refer to the exhibit. All of the vlans listed in the routing table below are trunked using 802.1q and are acti ...


Refer to the exhibit. SW1, SW2 and virtual switch are connected in a loop. SW1 and SW2 are standard layer 2 s ...


Refer to the exhibit. What issue does this topology present for the represented traffic flow.


Refer to the exhibit. A new device, PanelView, has been added to the network. See the table for device details ...