You create a checkpoint on a Cisco Nexus 7700 Series switch. You plan to roll back the runningconfiguration by us ...
based routing, which action is taken for packets that do not match any of the route
switch #configure terminalswitch (config) #interface ethernet 1/4switch (config
if) #switchport mode trunkswit ...
Which statement about enhanced zoning on Cisco Multilayer Director Switches is true.
Which statement about electronic programmable logic device image upgrades is true.
You plan to configure authentication for OSP
Which GLBL load
balancing method ensures that a client is always mapped to the same virtual MACaddress.
Which two features are required to implement a Layer 3 VXLAN gateway on the Cisco Nexus 5600 Seriesplatform.
Which command configures the aging for VLAN 100 to 500 minutes.
You experience an issue on a Cisco Nexus 7700 Series switch. You must gather detailed informationabout the system ...
list MY_ACLpermit tcp 2001:cc1e:aaaa::/64 2001:cc1e:befe:cccc::/64permit udp 2001:cc1e:bbbb::/64 200 ...
Which two options can be used for link aggregation when you configure vPC member interfaces.
Which two options should you consider when you configure a SAN zone set.
Which technology is required in the underlay to facilitate remote VTEP discovery.
Which statement about SNMP support on Cisco Nexus switches is true.
Which command should you ran to distribute NTP configuration changes by using Cisco Fabric Services.
You are connecting a Cisco Nexus 2300 Series FEX to a Cisco Nexus 5600 Series parent switch. Whichcommand should ...
On a Cisco Nexus 7000 Series router, witch statement about HSRP and VRRP is true.
What is the Overlay Transport Virtualization site VLAN used for.
Which Cisco MDS feature needs to be enabled for Cisco TrustSec FC Link Encryption to work.
What is an Overlay Transport Virtualization extended VLAN.
Which option must be configured when you implement a vPC.
Which protocol is used to exchange MAC address reachability between OTV
Which statement accurately describes the implementation of FSPF on Cisco MDS 9700 Series switches.
Which command should you run to enforce SNMP message encryption for all SNMPv3 communications.
Which statement accurately describes MP
You plan to implement the OSPF protocol whithin the data center network. Which two statementsaccurately describe ...
What can be identified by running the show install all impact kickstart bootflash:n5000
A Cisco Nexus 2000 Series Fabric Extender is connected to two Cisco Nexus 5000 Series switches via avPC link. Aft ...
When you configure LISP, which two components must be configured at the site edge.
You have a Cisco Nexus 5000 Series switch. Port security is configured to use sticky learning. Where arethe secur ...
Which two issues explain why a packet is not being routed as desired in a policy
Which option must be enabled to implement manual MACsec.
Which two protocols can be used to back up the configuration of a Cisco Nexus 5600 Series switch to aremote locat ...
Which two options accurately describe the implementation of Fibre Channel domain IDs.
Which LISP component provides connectivity between LISP and non
Which two Nexus family linecards allow the configuration of features regarding LISP, OTV and MPLS.
(Choose two.) ...
Which security feature is only supported on the Cisco Nexus 7000 Series Switch.
After enabling strong, reversible 128
bit Advanced Encryption Standard password type
6 encryption on aCisco Nex ...
You have two Cisco Nexus 7700 Series switches named SwitchA and Switch
Which action limits the maximum number of routes that are allowed in the routing table.
Which two items are services that are provided by Cisco Fabric Services.
You have two Fibre Channel switches that are connected via EISL. You discover that the fabrics areisolated. What ...
1(config) #feature vpcN7K
1(config) #vpc domain 113N7K
Which command should you run to limit IS
IS LSP flooding on a network.
What are two requirements for configuring SAN device aliases.
Which two statements are true when performing a SPAN capture of traffic reaching the Supervisor CPU inorder to tr ...
Refer to the exhibit. Which corrective action is taken to resolve the problem.
Which implicit rules are applied to all IPv6 ACLs.
What is the default Fibre Channel interface type for an FCIP virtual interface.
What are two ways to configure the switch ID for Cisco FabricPath.
You are configuring QoS on a Cisco Nexus 5000 Series switch. Which option is defined when configuring a CoPP pol ...
Which information does the show fcns database command display.
Which two statements are true when implementing fabric binding.
You configure STP on a switch that is attached to a Cisco FabricPath domain and that has the vPC feature deploye ...
What is the result when the configured RTT of an FCIP link is smaller than the measured RTT.
Refer to the exhibit. Which option is the result of the command.
Which technology relies on STP as a failsafe mechanism.
Switch(config) #login block
for 60 attempts 10 within 180 Switch(config) #login quiet
class acl R ...
Refer to the exhibit. You have a suboptimal outbound routing issue in the data center. Which two options can yo ...
When configuring OSPF, which two network types will avoid the DR and BDR election process between connected devi ...
You are configuring OTV between two data centers. On which interfaces should the site VLAN be allowed.
You have a Cisco Nexus 7700 Series switch on which the graceful restart feature is disabled. You are configuring ...
You have a Cisco FabricPath network. You must extend the network to support more than 16 million segments. What ...
When configuring HSPR on IPv6
enabled interfaces, which two commands are required.
Refer to the exhibit. Which two descriptions of the switch are true.
What is the purpose of the resequence command for ACLs.
Refer to the exhibit. You have a Cisco Nexus 7010 switch named N7k
1. Which command set should you run on a ne ...
Without having access to Fabric Path show commands, how can you confirm whether Fabric Path is configured on the ...
Fibre Channel IDs are dynamically assigned to which objects.
Which features must be enabled to implement manual MACsec.
You have a Cisco FabricPath network. You must implement vPC+ for a downstream switch. Which three actions should ...
Refer to the exhibit. Which statement regarding the outcome of the command is true.
Refer to the exhibit. What does the diameter command specify.
When configuring PIM to support an OTV implementation, which PIM configuration is supported in Cisco NX